Guides to facades, thermal insulation and wall anchors
External wall insulation and roof or loft insulation save the most energy in a house, but only if they are installed without thermal bridges and with enough material. This category contains a facade guide that shows how to calculate the area of elevations, gables and window reveals and how much adhesive, mesh, profiles and render go on each square metre. It explains adhesive consumption for insulation boards when they are bonded with the edge-and-dab method or over the full surface, and when the boards are anchored.
The wall anchor calculator works out the number and length of anchors from the insulation thickness, the substrate and the anchor pattern, while the U-value calculator shows how much insulation a wall, flat roof or loft floor needs to reach a target value. Tips describe a facade with plinth and reveals and insulating a loft floor. The work steps lead from preparing the wall to the final coat, and the list of common mistakes warns about dab-only bonding, anchoring too early and mesh without overlaps. Choose a calculator to get a material list per elevation.
Open the calculator: Facade (ETICS)
Other calculators in this category: Anchors · U-value and insulation
Guides
- How to Calculate Facade Area, ETICS Materials and Quantities – How do you calculate facade area? Multiply the house perimeter by the wall height, add the gables (base × height ÷ 2) and subtract windows and doors; then multiply the net area by the consumption of each ETICS layer and round up to whole packs. Here are the steps, a table per m² and a worked example.
Tips
- Attic floor insulation: how many cm of wool – How many centimetres of mineral wool a ceiling under an unheated attic needs for U 0.25, 0.30 or 0.20 – regulation, an 80 m² example and mistakes.
- House facade: plinth, reveals, profiles and anchors – How the calculator separates the plinth and reveals, counts profiles, reinforcements and anchors by edge zones, and how to mark shared house corners.
Step by step: Facade (ETICS)
- Clean the wall and check that it is sound and dry.
- Fix the starter track level.
- Apply adhesive around the edge and in dabs, or over the whole board.
- Bond the boards in a staggered pattern and anchor them once the adhesive has set.
- Embed mesh in the base coat with about 10 cm overlap.
- Apply primer and then the finishing render.
Quick tips for your calculation
- EPS adhesive consumption per m² depends on how flat the wall is: on an uneven wall apply adhesive around the edge and in dabs, on a flat wall across the whole board. Learn more
- Install facade anchors only after the adhesive has set; building edge zones need more anchors per m² than the middle of the wall. Learn more
- Leave a ventilated gap behind wooden cladding (usually at least 23 mm) with openings at the bottom and top, and keep the board ends away from the ground and rain splash.
- On roofs and ceilings keep the vapour control layer on the warm side: condensation inside the build-up reduces the insulation's performance.
- Insulation thickness has the biggest effect on the U-value; compare a few thicknesses before buying and check how much space you have for the build-up.
- Anchor length depends on the thickness of insulation, adhesive and old render – the anchor must reach deep enough into the load-bearing wall.
Common mistakes
- EPS boards fixed with dabs only – Apply adhesive around the edge and in dabs, or over the whole board on a flat wall.
- Mesh without overlap – Overlap the mesh by about 10 cm and embed it in the base coat.
- Anchoring too early or too short – Anchor after the adhesive has set, using anchors of the right length.
- One measurement per wall – Measure at two heights and check the diagonals.
How to use the calculator
- The target U is your decision or a regulatory requirement:
• Legal limits depend on the country, building type and element (wall, roof, ceiling)
• Take the value from the current regulation and note the source and date
• Enter it in the calculator as the target
The calculator works out the theoretical thickness of the main layer and, with available catalogue thicknesses, the nearest larger one.
All guide categories · Frequently asked questions about the calculators