Guides to screed, self-levelling compound and floor finishes
A flat, dry base is the foundation of every floor, whether it will receive tiles, laminate, parquet or a decorative finish. This category contains guides on sand-cement screed and on self-levelling compound: how much compound you need per square metre for each millimetre of thickness, when a thicker screed is the better choice and when a thin layer of compound is enough, and how long each layer must dry before the floor covering goes down. An overview guide on preparing and laying floors links all the steps from measuring to the final layer.
Next to screed you will find floor finishes that need a carefully prepared base: an epoxy floor for a garage or workshop, microcement for bathrooms and stairs, and stone carpet for terraces and balconies. For each of them there are work steps, short tips on primer and moisture in the base, stone carpet consumption per m² and the most common mistakes, such as laying on damp screed or leaving out the edge strip. Choose the right calculator and you immediately get bags, kilograms and packs for your floor area.
Open the calculator: Self-Leveling Compound
Other calculators in this category: Floor Screed · Epoxy floor calculator · Microcement calculator · Stone carpet calculator
Guides
- Self-Levelling Compound per m²: Calculation by Area and Layer Thickness – Short answer: kg needed = area (m²) × average layer thickness (mm) × consumption (kg/m² per mm), rounded up to whole bags. The calculator uses 1.7 kg/m² per mm; self-levelling compounds typically need 1.5–1.7 kg/m² per mm, so for a specific product the data on its pack or data sheet applies. For 20 m² at 5 mm the calculator gives 170 kg, i.e. 7 bags of 25 kg.
- Floor Preparation and Tiling: Which Tool When – An overview of the job from the subfloor to laid tiles. For each step there is a tool that calculates the quantity or layout and a guide that explains the decisions. The tools build on each other: the 2D planner passes the area, format and joint to the tile calculator and the room area to the self-levelling compound calculator, so you do not enter the data again.
Tips
- Epoxy garage floor: roller coat or self-levelling – How much primer, epoxy, quartz and topcoat a 6 × 3.5 m garage needs – roller coat or 2 mm self-levelling layer, and which packs to buy.
- How much self-leveling compound for a whole flat – How to split a flat with different layer thicknesses into calculations, add up kilograms and bags, and what to watch at thresholds.
Step by step: Self-Leveling Compound
- Clean the substrate of dust, grease and loose material.
- Apply primer and let it dry.
- Mark the layer height and fit edge strip along the walls.
- Mix the compound with the exact amount of water from the instructions – never add more.
- Pour in strips, spread it and de-aerate with a spiked roller.
- Protect from draughts and sun until the compound has dried.
Step by step: Floor Screed
- Clean the base and fix pipes and services firmly.
- Lay insulation, overlapped sheeting and edge strip along the walls.
- Set screed rails at finished floor height and check any fall.
- Mix the screed to an even, earth-moist to flowing consistency for its type.
- Spread, compact and level it with a straightedge along the rails.
- Keep it moist for the first days and measure moisture before laying the floor finish.
Quick tips for your calculation
- Self-levelling compound uses about 1.7 kg per m² for every millimetre of thickness, so each extra millimetre on 20 m² needs about 34 kg more. Learn more
- Clean the substrate and apply primer before pouring self-levelling compound; without it the base draws water from the mix and it can crack. Learn more
- Cement screed dries slowly: measure the moisture of the screed before laying parquet or tiles instead of relying only on the number of days. Learn more
- Fit edge insulation strip along walls, columns and pipes – a floating screed must not touch the wall anywhere. Learn more
- Stone carpet aggregate and substrate must be completely dry; moisture can leave cloudy stains and weaken the binder.
- Apply epoxy coating only to a dry, sound substrate: new concrete must cure first, and the surface needs grinding and thorough dust removal.
- Microcement is a thin layer that copies every crack below it, so repair cracks and joints and reinforce them with mesh before applying it.
Common mistakes
- Self-leveller without primer – Clean the base and prime it before pouring.
- Self-leveller poured too thick – For thicker layers use a screed or a compound made for that thickness.
- Flooring laid on wet screed – Measure screed moisture and lay only when it is below the permitted limit.
- Screed without edge strip – Fit edge strip along walls and columns and movement joints to suit the bay size.
- One measurement per wall – Measure at two heights and check the diagonals.
- Plastering an unprepared wall – Clean the wall and apply a primer or spatterdash coat suited to the substrate.
How to use the calculator
- In Rooms mode add each room; the calculator adds up the areas and uses one layer thickness for all of them.
If rooms need different thicknesses, do one calculation per thickness and save them to the same project. For buying, add up the kilograms, not the bags. The calculator does not add an allowance; it only rounds up to whole bags. - 1. Measure the length and width of the surface and multiply them to get m².
2. Choose one of the 7 systems.
3. Set the primer, epoxy and topcoat rates and the number of coats (for the self-levelling system, the thickness in mm).
4. Optionally pick decorative chips.
5. Press Calculate.
Example: system 3 on 50 m² gives 60 kg of material to buy (primer 20 kg, epoxy 30 kg, topcoat 10 kg). - The table shows the calculated consumption in kg and the packs to buy. Primer comes in 30 and 10 kg packs, epoxy in 30 and 16 kg, topcoat in 5 and 1 kg. The quantity to buy is the sum of the packs, so it is usually larger than the calculated consumption. Quartz and chips are shown in kg without packs. For real quantities, check the manufacturer's technical data sheet.
- In the calculator, optionally select decorative chips.
Norms: 150, 350 or 500 g/m², or full flake at 1.1 kg/m². For full flake the topcoat is about 333 + 167 g/m². Chips are shown in kg, without packs. - Stone is counted in bags of 25 kg, rounded up to whole bags.
Example: 10 m² with a 10 mm layer = 150 kg of stone = 6 bags of 25 kg. The allowance for edges and steps increases the quantity.
All guide categories · Frequently asked questions about the calculators