Guides to skim coating and painting walls and ceilings
Skim coating and painting are the most common finishing jobs in a home, and also the most common reason paint is bought twice or bags of filler are left over. This category contains guides on skim coat consumption per square metre and on paint coverage for walls and ceilings, with tables for one and two coats. They explain how to calculate the wall area without doors and windows, why the ceiling is calculated separately and how many tins you need for one room or a whole flat.
The page also brings together tips on the number of coats, on priming new plaster and plasterboard, and on covering a dark wall with a light colour. The step-by-step section takes you from cleaning and filling cracks through skim coating and sanding to the second coat of paint. You will also find common mistakes, such as painting without primer or forgetting openings in the calculation, and instructions for entering several rooms or just the total area. The skim coat and paint calculator then gives kilograms, bags, litres and tins for the whole job.
Open the calculator: Paint, Putty & Plasterboard
Other calculators in this category: Wallpaper & wall panels
Guides
- Paint Consumption per m²: How Much Paint for Walls and Ceiling – How much paint do you need for a 50 m² wall or room? The calculator uses 0.125 l of paint per m² per coat, so 0.25 l/m² for two coats, in 15 l buckets: for 50 m² that is 12.5 l, or one bucket.
- How Much Putty per m²: Skim Coat Consumption for Walls and Ceilings – Short answer: the calculator uses 1.5 kg of putty per m² for two coats, in 25 kg bags. For 50 m² that is 75 kg, so 3 bags; one 25 kg bag covers about 16.7 m² in two coats. A 4 × 5 m room with the ceiling (63.3 m² net) needs 95 kg, so 4 bags.
Tips
- How much paint and putty for a room or flat – Room-by-room calculation: openings, ceiling, a tiled bathroom, ceiling and walls in different colours, and the total bags and buckets for a flat.
Step by step: Paint, Putty & Plasterboard
- Protect the floor and joinery and clean the wall.
- Fill holes and cracks and apply skim coat in thin layers.
- Sand, remove dust and apply primer.
- Apply the first coat with a roller and cut in the edges with a brush.
- When dry, apply the second coat in the same direction.
- Check under side lighting and touch up where needed.
Step by step: Wallpaper & wall panels
- Fill holes and cracks, sand bumps and remove old wallpaper and dust.
- Measure walls and openings, check that all rolls share one batch and mark a plumb line for the first drop.
- Prime according to how absorbent the surface is and let it dry.
- Mix the paste as instructed and apply it to the wall or the drop, depending on the wallpaper type.
- Hang the first drop on the plumb line, butt the next ones against it with the pattern matched and smooth out bubbles.
- Trim the excess with a sharp knife at the ceiling, floor and openings and wipe paste off the seams straight away.
Quick tips for your calculation
- When you calculate how much paint you need for walls, count two coats; dark or bright colours and fresh plaster often need a third coat or a primer. Learn more
- Apply skim coat in thin layers and sand each one – a thick layer cracks and uses more material. Learn more
- With a large pattern repeat, cut each drop only after lining up the pattern with the previous one; keep the offcuts for the short pieces above doors and windows.
- Leave timber boards and panels in the room for a few days before fitting, and leave a movement gap at the floor, ceiling and walls that the finishing trims cover.
Common mistakes
- Painting without primer – Apply primer first, then two coats of paint.
- Plastering an unprepared wall – Clean the wall and apply a primer or spatterdash coat suited to the substrate.
- Forgotten openings and reveals – Subtract openings and add reveals separately.
- Wallpaper rolls from different batches – Buy all rolls at once from one batch, with extra for the repeat, and check the batch number on every roll.
- Panelling without an edge gap – Leave a gap at the floor, ceiling and corners, cover it with a trim and fix the panels to battens at the right spacing.
How to use the calculator
- 1. Enter the room dimensions (length, width, height).
2. Choose what you are painting: walls, ceiling or both.
3. Enter the number and dimensions of windows and doors - these are deducted automatically.
Tip: White is often used for the ceiling, and a tone-on-tone or contrast colour for the walls. - The calculator supports two modes:
1. By rooms - enter the dimensions of each room
2. Total area - quick entry if you know the m²
For each room you can choose what you are painting (walls, ceiling) and deduct openings.
All guide categories · Frequently asked questions about the calculators