Wallpaper & wall panels
Quick answer: A 4 × 3.5 m room, 2.6 m high, with a 1.2 × 1.4 m window and a 0.9 × 2.0 m door needs 30 drops of 53 cm wallpaper; with no pattern repeat that is 9 rolls of 0.53 × 10.05 m (3 drops per roll) and about 7.1 kg of paste.
Wallpaper calculator: drops per wall, rolls with pattern repeat, paste; tongue and groove, PVC, MDF, slat and 3D panels with battens and trims
How the calculation works
The wallpaper calculator works wall by wall: the number of drops is the wall width divided by the roll width, rounded up. Short pieces are cut above and below windows and doors, and every drop gets a trimming allowance and is rounded up to the pattern repeat. Pieces are laid out on the rolls from the longest to the shortest, so you see how many rolls of wallpaper to buy and what is left over. In wall-panel mode the same walls give panels (tongue and groove, PVC, MDF, acoustic slat and 3D panels), battens at a spacing, plugs, clips or adhesive and trims.
Inputs and units
- Walls: width and height in metres; openings with width, height and sill height (doors have a sill of 0)
- Roll: width and length (default 0.53 × 10.05 m), pattern repeat in cm and straight or offset match
- Trimming allowance (default 10 cm per drop), paste in kg/m² (default 0.2), optional primer and lining paper
- Wall panels: type, cover width and panel length, direction, waste, batten spacing, fixing and trims
Formula and assumptions
Drops = ⌈wall width ÷ roll width⌉. Cut length = ⌈(height + trim) ÷ repeat⌉ × repeat, plus ½ repeat for an offset match. Drops per roll = ⌊roll length ÷ cut length⌋; rolls = rolls used after laying out all pieces (longest first). Paste = net area × kg/m². Panels: pieces per wall laid out on the panel length × (1 + waste); battens = (⌈span ÷ spacing⌉ + 1) rows.
Worked example
Room 4 × 3.5 m, 2.6 m high, 1.2 × 1.4 m window and 0.9 × 2.0 m door: 35.52 m² net, 30 drops, 2.7 m cut, 3 drops per roll, 9 rolls of 0.53 × 10.05 m and 7.1 kg of paste. With a 64 cm repeat you need 10 rolls, and with a 64 cm offset match 14 rolls.
Typical starting values (editable)
| Item | Default | Note |
|---|---|---|
| Wallpaper roll | 0.53 × 10.05 m | 0.70 m and 1.06 m also exist |
| Trimming allowance | 10 cm per drop | top and bottom |
| Wallpaper paste | 0.2 kg/m² | check the instructions |
| Batten spacing for panels | 40–60 cm | depends on the panel type |
What affects real consumption
- Pattern repeat and match type: a large offset repeat adds many rolls.
- Number and size of windows and doors and the wall height.
- Roll width and panel length compared with the wall height.
Common mistakes
- Counting rolls from area alone, without drops and repeat.
- Buying rolls from different batches (shade difference).
- Wall panels without an edge gap and without battens at the right spacing.
Limits of the calculation
- Where an opening sits across the wall is unknown: drops only partly covered by an opening count as full drops.
- Paste consumption, batten spacing and fixings are starting assumptions, not manufacturer data.
- Sloping walls and ceilings are not modelled separately – enter them as a rectangle.
- Exterior wood cladding of a facade is calculated in the facade calculator.
Frequently asked questions
How many rolls of wallpaper do I need for a room?
Work out the drops per wall (wall width ÷ roll width) and how many drops one roll gives. A 4 × 3.5 m room, 2.6 m high, with a window and a door needs 30 drops and 9 rolls of 10.05 m.
What is a wallpaper pattern repeat?
The distance at which the pattern repeats. Every drop is cut to a multiple of the repeat, so a larger repeat means more waste and more rolls.
What is the difference between a straight match and an offset match?
With a straight match the pattern sits at the same height on every drop; with an offset (drop) match every second drop is shifted by half a repeat, which uses about half a repeat more per drop.
How much wallpaper paste per m²?
The calculator starts with 0.2 kg of mixed paste per m²; enter the consumption printed on your pack instead.
How many PVC panels or tongue and groove boards for a wall?
Columns = wall width ÷ cover width; pieces are laid out on the panel length and waste is added. A 4 × 2.6 m wall with a window needs 15 PVC panels of 25 cm × 2.7 m.
What batten spacing for wall panels?
Usually 40–60 cm, at right angles to the panels; the system instructions give the exact spacing. The calculator counts batten rows, their length and the plugs.
Related calculators
Publisher: Art-Visum d.o.o. · Content reviewed:
Calculations use common consumption rates and manufacturers' technical data sheets; results are estimates. Methodology · Standards · About