Tiling guides: quantities, layout and laying
This category collects everything you need to know before you buy tiles for a bathroom, kitchen, hallway or patio. You will find guides on how many tiles you need for a floor or wall, how much tile adhesive goes on each square metre and how much grout a given joint width uses. Tips explain the cutting allowance, large-format tiles and why boxes should come from the same batch.
The floor covering planner helps you start the layout from the right corner or from the centre of the room, so you do not end up with thin strips along the walls that are hard to cut. The tile levelling calculator works out clips and wedges for a flat surface without lips between tiles. The page also shows the work steps from measuring to grouting, the short tips the calculator displays next to the result, the most common tiling mistakes and instructions for entering several rooms. Once your measurements are ready, open the tile calculator to get the number of tiles, boxes, bags of adhesive and grout for the whole job.
Open the calculator: Ceramic Tiles
Other calculators in this category: 2D Flooring Layout Planner · Levelers
Guides
- Tile Layout Planning: Where to Start Tiling Without Thin Cuts at the Wall – Short answer: measure the length you are tiling, divide it by the tile pitch (tile + joint) and look at the remainder. If a thin strip would be left along one wall, move the starting point so the cuts at opposite walls are equal and wide enough. In the 2D planner you choose between the starting points “From the corner”, “Piece in the centre” and “Grout line in the centre” and, before buying, see the number of full and cut pieces, the narrowest cut and the purchase quantity.
- How many tiles do I need: pieces, waste allowance, adhesive and grout – Short answer: required area = net area × (1 + waste allowance), and tiles = required area ÷ area of one tile, rounded up. For a 4 × 5 m room (20 m²) with 60 × 60 cm tiles and a 5 % allowance that is 21 m² and 59 tiles. Below are the steps, the allowance per laying pattern, adhesive, grout, packaging and common mistakes, with examples calculated by the tile calculator.
Tips
- How many tiles to buy: cuts, waste and boxes – Net area versus purchase quantity, cut pieces and offcuts, an allowance added only once and rounding to boxes – with examples from the tile calculator and the 2D planner.
Step by step: Ceramic Tiles
- Measure the area and choose the tile size; the tile calculator adds waste for cuts.
- Check the substrate with a 2 m straightedge and level larger deviations.
- Clean the substrate and apply a primer suited to it.
- Spread adhesive with a notched trowel; for large tiles butter the back as well.
- Lay from the centre line or the most visible wall, with spacers or a levelling system.
- Grout only after the adhesive has set and wipe off excess grout with a damp sponge.
Quick tips for your calculation
- For tiles of 60 cm and larger, allow more waste and more adhesive per m²: large formats need a trowel with bigger notches and adhesive on the back of the tile too. Learn more
- Buy all tiles from the same batch (same shade and calibre) and keep a few spare pieces after the job for later repairs. Learn more
- Start the tile layout from the room's centre line or the most visible wall, so narrow cuts do not end up at the entrance or by the door. Learn more
- Leave laminate and parquet in the room for at least 24–48 hours before laying, and keep an expansion gap along every wall. Learn more
- A tile levelling system does not fix an uneven substrate – it only keeps the edges of neighbouring tiles flush while the adhesive sets. Learn more
Common mistakes
- No spare tiles – Add a reserve for the size and pattern and buy everything from one batch.
- Spot-fixing tiles – Spread adhesive with a notched trowel over the whole surface.
- Grouting too early – Grout only after the adhesive drying time given in the instructions.
- Large tiles on an uneven floor – Level the substrate and use a tile levelling system.
- One measurement per wall – Measure at two heights and check the diagonals.
How to use the calculator
- 1. Measure the length and width of the room in meters.
2. Enter the tile dimensions (e.g. 60x60 cm).
3. Select the surface type (floor or wall).
4. Add a 5-10% reserve for cutting.
Example: Bathroom 2.5m x 3m = 7.5 m². With a 10% reserve you need ~8.25 m² of tiles. - The calculator supports adding multiple areas:
1. Click 'Add area'
2. Enter the dimensions of each room
3. Give each area a name (e.g. 'Bathroom', 'WC')
The calculator adds up all areas and gives a total material calculation. - 1. In the planner, choose the room shape.
2. For L and U, enter the lengths of the legs.
3. For a free-form room, draw the outline; walls are horizontal and vertical.
4. Add columns as rectangles inside the room.
If the shape is not valid (walls cross), the planner shows a message. - The planner shows the number of full and cut pieces, the area, the waste and the number of packs. The purchase is an estimate: except for the pattern that reuses offcuts, every cut piece counts as a new piece. Actual dimensions on site may differ, so keep an allowance.
Skirting, underlay, vapour barrier and transition strips are shown separately in the “Additional materials” card. - Yes. Choose the material (tiles, laminate, vinyl or parquet), enter the plank dimensions and the number of pieces per pack. For planks you can enable reuse of cut offcuts and set the minimum joint offset between neighbouring rows.
- In “Extras” switch on only what the room has:
• Door and threshold: a door on the selected wall; the flooring can run into the opening up to the threshold, and the transition strip is as long as the door is wide.
• Angled walls / corners: enter the shape as wall lengths and angles or as coordinates.
• Border along the walls: one row of tiles along each wall, with an offset from the wall.
• Mixed formats: Versailles (4 sizes) or a combined pattern of 2–3 sizes; boxes are counted per size.
• Wall tiles (bathroom): walls with doors, windows, niches and reveals.
Options that are off do not change the layout. - The leveling system calculator shows a pyramid-shaped table:
• the row is the long side of the tile, the column the short side
• each cell shows the number of levelers per m² for that format
• tapping a cell selects the format for the calculation
The table is the same data the calculator uses for the result.
All guide categories · Frequently asked questions about the calculators